In this article, we look at how to install an AGP artwork card for your computer. Installing computer components is usually tricky if you’ve never performed it before.
But My partner and I trust we’ll show you that a lot of tasks have a “plug a great play” functionality to them. The identical is valid with the AGP visuals card. The term AGP represents “Accelerated Graphics Port” and is the specific slot on your desktop where you will install your visuals card. You will simply fall the AGP graphics credit card into this slot and be good to go.
1 . Power Lower Your System
To install video credit card components correctly in your personal computer, you must first power your body down. These are a couple of safety precautions.
Make sure your computer is completely shut down before installing video card parts or any other internal portion, for that matter. After you shut down your personal computer, you also need to cut off the juices to the power supply. If you’ve never done this before, have a look at the back of your computer. You might have a switch where the power is. Flip that swap into the off position. Ultimately, pull the AC electric cord.
It may have never occurred to you personally that you would need to do this, but we must explain how to install computer parts correctly. Rule 1 is always to ensure no power is entering the system. Any latent spikes will fry your system in a heartbeat and could injure an individual.
2 . Opening Up your computer Case
Next, we will open up the case. Since I’m learning how to install an AGP graphics card, and that playing card goes inside your computer, I have to remove the case below.
Tend to worry about this procedure, though. Maybe you have experience in knowing how to run computer components like additional hard drives, but you said you might never poke around your respective computer. It’s not this hard.
Before you can open your case, you need to determine what kind of case you have. That can determine how your particular case shall be opened. If you have something like a new mini-tower, you can open this situation by removing one of the edge panels. Be sure to remove the aspect that’s above the motherboard. Remove the screws in the back of your computer that holds the panel on the chassis and then lift up it off.
However, some more mature-style cases demand that you remove the whole backside cover and glide the chassis out. Look at your particular model and see just how it’s designed.
3. Get rid of the PC Slot Cover
For one which just installs video card parts like the AGP graphics credit card, you will need to remove the PC position cover in the back of the computer.
Glance at the back of your computer, and you’ll observe what we mean. There are a group of several metal latches confronting the slots where you can put in internal computer components. One or two screws tack down several metal latches. When it reaches time to insert a factor, like a modem, for example, you simply must first remove the metal latch in front of the slot before you habitually the component.
With the AGP graphics card, the process is the same. First, locate often the AGP graphics card video slot. Only one slot can correctly match your playing card, so you’re in good luck. Then unscrew the sheet metal latch in front of the AGP artwork card slot, often slide the latch out, and often set the screws in a safe spot.
4. Installing the AGP Card into its Slot
The part you’ve been looking forward to is also available, knowing how to install an AGP graphics card into its position. Again, only one credit card on the motherboard complements your AGP card; thus, don’t worry about putting that into the wrong slot.
If you are unsure, look at the bottom of the AGP card to match upward with possible slots for you. The AGP card position stands out from all other slot machine games on your motherboard inside its little corner.
As you seek, align the AGP artwork card above its video slot. Hold the card with your hands and fingers from both ends, in addition, to pressing it down into often the slot until it seats securely. Make sure that it’s firmly clicked into the slot. If anyone the main card is sticking out, generate it back in. Then protect the card into the motherboard by screwing the retaining twist.
5. Promoting In the Monitor, Closing Right up and Powering Up
With the card adequately installed, they have time to plug in your screen. That wasn’t so bad, was it? Little by little, you’re finding out how to install computer components before becoming a pro! Locate your monitor cable and plug it into the AGP card monitor connector.
If the card has more than one plug, this means that your card supports more than one monitor. Check your documents to determine which is the appropriate plug for your monitor. Plug it in, and you should be good to go!
It is not time to close up and switch on. Place the computer cover backside onto your computer. Screw that back on using the anchoring screws that (hopefully) you kept in mind to set in a safe location earlier. Now it’s time to switch on.
Flip your power supply switch back on, and plug the AC wire into a wall outlet. After that, reboot your computer. To properly install video card elements, as with other components, you should also try to install software drivers. Find the CD that came together with your card and insert into your computer when it reboots. The actual instructions to install the appropriate software program drivers.
Conclusion
Congratulations, you might pass another milestone in mastering how to install computer ingredients! We think you’ve determined that it’s not all that tough. The components and motherboard should fit together like pieces of a puzzle.
On older methods, you may find that your computer runs on the PCI slot and credit instead of the AGP card. Regardless, the general process is similar. Don’t forget to consult the paperwork that comes with your hardware whenever you feel stumped. Use very little common sense and follow safety precautions. Your new card is going to be up and running in no time.
Read also:
